Glipic PCB


	*We Stand!*

	*UNITED*


	AVR Kits




*Site Sections*

Classified Section Items Available

Microchip PICDEM USB dev board -- like new! $95.00

Click Here for details

Users’ Section

Available

If you have any projects that you would like displayed, please send E-mail

Contact

E-mail for more information




	GLiPIC Shown assembled


	The GLiPIC board designed for KS0108 controller based LCD modules, either the 128x32 or the 128x64 displays. With the adapters available it can also be used with T6963C and SED1330 controller based LCD displays. Plus, it can be used as a general purpose controller since most pins are brought to headers. With a *bootloader* *the PIC can be programmed via the serial port.*

		I have a limited number of the GLiPIC pcb and associated parts available for purchasing. Below are the items available.

Measures only 1.9 x 2.5”! Double sided board with plated through holes. Includes the assembly manual detailed with color pictures and parts placement layout.

Includes: The GLboard, manual, passive components, connectors, a 20MHz crystal, an LM7805, a PIC 16F877-20, a 24C256 I2C eeprom (can hold up to 32 screens of images!), a MAX232, and a 128x64 Graphic LCD.

GLboard Rev D

GLBC -- $19.00

GLiPIC Shown assembled

Complete Unassembled Kit

Parts may vary in size and color

GLKLCD --- $95.00

GLKIT -Without the LCD -- $50

How to order


	KS0108 controller based LCD module 128x64.


	For details on the GLI2 Development board click here




			GLI2 Development kit

		How to order


	For Seiko G321D 320x200 or similar LCD adapter kits




				AD321A $26.00



			AD321B $23.00


	Designed to accomodate large LCD displays by providing -36v for the LCD drivers. Uses Max637 ICs.

Similar to the AD321A but provides a maximum of -24v. It utilizes a pre-assembled TDK CE73 inverter. Works with the G321D 320x200 display.

		How to order


	SED1330 based LCD 256x128 graphic display and adapter


	256x128 Graphic LCD with SED1330 controller.


	*Large display area almost 2.75”H x 5.0”W!*

Overall size (pcb area) 4.5”H x 5.75”W. This Hyundai LCD display is not backlit. However, there seems to be provisions for some type of backlight since there is a 2mm gap between the board and the LCD panel. The SED1330 is a popular controller and has many features. Documentation for the controller is available from numerous sources on the Internet. You can also download it from Epson’s website.

		Adapter Kit




	Sanyo 240x64 T6963C based graphic lcd

			(no backlight)


	GLiPIC Board adapter kit for the 256x128 SED1330 LCD (can also be used with T6963C based LCD’s). Two headers are provided a 1x18 and a 2x10. The unit has an on-board 5v to -15v convertor, a MAX637, which supplies LCD negative voltage (Vee). A 20K POT is used for the Vee adjustment. Includes parts shown below.

Complete Kit GLSEDK $98, includes the GLiPIC kit, the adapter kit and the 256x128 graphic LCD. or Complete Kit GLT69K $98 with the Sanyo 240x64 LCD Save $15 form individual price list.


	Adapter shown assembled. 0.9”H x 2.5”W


	GLiPIC Shown assembled


	How to order

Individual Price List*

GLADPS2 Adapter kit $23
LCDSED* 256x128 Graphic LCD $40
GLKIT GLiPIC controller board kit $50


	* LCDSED Includes bare GLADPS2 adapter pcb & header pins




	The GLADPS2 adapter kit

	Bare pcb supplied when ordering LCDSED


	20 contact connector and carrier pcb for TAB/COG LCDs which have a 0.5mm pitch 20 contact Flat Flex ribbon cable. The carrier can fit in a standard 0.6” wide 20 pin IC socket





	20 contact Flat Flex connector and carrier pcb kit. (Requires soldering) COG128 - $10.00




	Shown assembled


	Right: Shown assembled and connected to a 128x64 Graphic LCD (LCD not supplied)


	How to order




Included


	MCPROTO


	MMC socket holders tiny pcb with a small proto area 1.2”x2.5” It will hold either the shielded or unshielded MMC sockets as shown on the left. Includes an MMC socket. With proto area shown on the left and without on the right $16.00

		How to order




			MMC-APD1

		With 2x5 header




			MMC-APD2
	With 1x6 header


	Includes resistors, header and MMC socket


		Max233A Serial I/O adapter

	A tiny serial I/O (TTL to RS232) I/O adapter. Ideal for projects that only occasionally require I/O or in-circuit programming. Eliminates having to place an RS232 transceiver on every project board. Uses a Max233A IC or equiv. Provided is a DB9 connector for use with a terminal or PC. Signal and power pins connect to your project board via any 4 wire connection, providing +3.3 - 6v, Ground, TTL Rx and TTL Tx.for the AD233A


	AD233AK Complete kit $19.00


	Shown assembled


	How to order




AD233AP

	Bare PCB

		$8.00




AD233BP

	Bare PCB

		$9.00


		Model AD233BK

	Same as the popular AD233AK except that it includes the pinouts for CTS/RTS handshake signals (via the MAX233). The CTS/RTS pins can be jumpered if handshaking is not required

	AD233BK Complete kit $20.00




		PCB Layout




	MMCP3A pcb $23.00


A complete development board for use with an MMC storage card. It houses a PIC16F876 mcu, 24LC64 I2C eeprom, Max233A for serial I/O and ISP programming, an LM2937 3.3volt regulator, 10MHz xtal, power LED and reset switch. It can house either the Shielded or unshielded Molex MMC socket. Only PortC of the PIC is used, Pins for PortA and PortB are brought to headers for general use. Dimensions: 1.9x2.5 inches Click here details

	How to order

		MMC3KE -- $56.00


	The MMC3BPB pcb can accomodate either DIP8 or SOIC8 I2C eeproms. This makes it possible to use 3.3 volt FRAMs from Ramtron, Inc. which have no wait states and have no limits on the number of write cycles.

	MMCP3B pcb $25.00


	MMC Complete kit, includes a PIC16F876, Max233 (or ADM233), I2C eeprom, 10Mhz xtal, MMC unshielded socket, DB9F connector, reset switch, led, LM2937 regulator and all capacitors and resistors. Supply voltage: 5-12v DC. Does not include a MMC flash card


			24LC256 Eeprom Version

		MMC3KF -- $59.00

			FM64CL FRAM Version


		MMC3KE shown assembled with shielded MMC socket


	For information on the MMSD3 Kit click here


	MMSD3 Kit for MMC as well as SD cards (in non-secure SPI mode)


	*Useful tiny carrier! Use existing DIP8 sockets to try out new SOIC8 devices such as a FRAM to replace a standard eeprom.* *Available in the parts section* *( includes mounting pins )*


SOIC8 to DIP Carrier pcb




	S8D8P $3.00 (includes pins)

		Shown with a FRAM mounted


	How to order


	Mini Power Supplies

Mini Power Supplies for breadboards 5v, 3.3v and dual voltage modules for quick prototyping and projects. Standard pins easily connects to pcbs and development boards.












			[an error occurred while processing this directive]




	PSU53PB $4.00